Thursday, August 22, 2013

Canon GENERIC "S" SERIES RESET CODE

Tags
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in
succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the
"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout. javascript:void(0)
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.

resetter epson r230x (SSC Service Utilily)

Tags



1. Make sure the printer is turned on and terkonek with a computer (printer driver already installed)
2. Install SSC Service Utility and run the program
3. Model of printer configuration settings. Select the Epson Stylus Photo R230. After the play closed

   windows.
 4. In the lower right corner of the taskbar (near the clock) right click the icon SSC Service Utility, select
     " Protection Counter" click "Reset protection counter" select Yes on the pop up that asks
    "Have you  Replace waste ink pad"

 







5. Restart the printer, the printer is ok

That's the steps I described to my friend, so she does not go back and forth to the printer lift handyman service to reset Epson R230. May be useful.


               Link Download File:
http://adf.ly/7tyCh


Canon Pixma IP2770 Error 006

Tags
To resolve Error 006 on Canon iP2770
1. Canon iP2770 Driver uninstall then restart
2. then install again
3. do reset the service tools program
4. print as usual
5. completed

Canon Pixma IP2770 Error 5100

Tags
Error 5100 occurred at Canon iP2770 Printer This is usually caused because they are not detected by the Printer Cartridge. So the message Error 5100 We inform that the printer can not find its cartridges. Steps that must be done
1. Turn off the printer
2. Remove both cartridges from the printer
3. Use a cloth moistened with alcohol to clean the surface of the contact / terminal connector that touches

    Cartridge printer / could also use a pencil eraser
4. Replace the two Cartridge
5. Turn on the printer.

Printer Canon IP2770 Error 5200

Tags
When iP2770 is turned on, the printer looks normal with LED Flash GREEN. But after ordered to do pengeprinan, the error 5200 would show up, and the LED will turn green ngeblink orange 1x to 8x
For error 5200 Printer Canon IP 2770/2700 is the same as I fix Error 5B00 above but for this error problem you just need the first step Error 5B00 following:


1. Make sure that the printer Canon IP 2770 / IP 2700 is turned off (Off) But the power cable  


    (power) installed.
2. Press the RESUME button for about 2 seconds
3. After that you press the POWER button until the green light on (when pressing the POWER button,

    Resume button not released yet)
4. Then release the RESUME button, but do not release the POWER button.
5. POWER button while still depressed, press the Resume button 5 times. Led will light turns green to

    orange last flame orange. (not to be mistaken 4x because the printer will die in total, but also temporary)
    while reading the writing on the nature of the above.
6. Release both buttons simultaneously.
7. LED will blink briefly then will flash GREEN.
8. The computer will detect the new device, just ignore it
9. Press the Power button so that the printer OFF / Off
10. Once the printer is completely dead then press the Power Button Back then the computer will turn on

    and be ready for use again.

Service tool pixma ip2770 (Resetter Pixma iP2270)

Tags

steps reset canon pixma iP22700: 
 - Log on to the service mode first connect the printer to the computer and the power cord without turning
  on the printer (the printer is turned off). 
- Press the Resume button about 2 seconds and then press the POWER button until the green light on 
   (when pressing the POWER button, Resume button jgn removed) 
- Then off the RESUME button, but do not release the button POWER
While the POWER button still depressed, press the Resume button 5 times. Led will light turns green to
   orange last flame orange. (not to be mistaken 4x because the printer will die in total which means that the 
   steps we have to reinstall from scratch)
- Then release both buttons simultaneously, the LED will blink briefly then will flash GREEN.
- At this time the computer will detect a new device, just ignore it and wait until the process is complete.
- This situation shows the iP2770 printer is in a state of SERVICE MODE and ready to reset

for permanent service
  
1. Download Resetter
2. Exctract File Resetter iP2770. 
2. Service Tool ServiceTool_V1050



 

3. Click the "MAIN", then the printer will proceed, then iP2770 will print one page
    with the words "D = 000.0
4. Click "EEPROM Clear".
5. Then click "EEPROM", and the printer will print the results iP2770 Resetter. One line in his writings as 
    follows: "TPage (TTL = 00000)" 
5.  Turn off the printer by pressing the POWER button.
6. Up here if all goes well, it's too printer will reset and is back Normal.

the following ink may have run out calour canon MP250, IP 2270, MP160, iP2700

When the printer is turned on seems OK, but after the print command, it will display Blink 13x Orange on the Canon MP250, MP160, iP2770, iP2700


 the following ink may have run out Color

Blink 13x Orange lights with the picture above, means catrid color reset press the Resume button requires a bit longer until the GREEN light flashes, then release. black catridge also need to be reset and the picture is as follows:

 the following ink may have run out Black



Same way: rather long press the Resume button until the GREEN light flashes, then release.after doing these steps then the printer will return to normal. This often occurs when the cartridge runs out complete refill then installed again.